Every technician is IICRC certified and has handled hardwood floor water damage many times. You get a clear plan before any work starts.
You focus on your home. We put together the photos, readings and reports your insurance company needs.
The quote is free and you see the price before work begins. No surprise charges at the end.
When you call about hardwood floor water damage, you reach a restoration team that works in Silver Spring every day. We tell you what it will take, give you a clear quote and get a crew moving.
It does not take long for water to change a wood floor. Boards take on moisture from below and from the edges, swell against each other and start to cup, with the edges rising higher than the center. A floor in this condition is not necessarily ruined. Boards of solid wood often return to flat if they are dried during those early days. What matters is removing moisture from the wood and from its subfloor steadily and under control.
Our tool for hardwood is the floor drying mat. A vacuum unit attached to the sealed mats lifts water out by way of the seams and the wood itself, and dehumidifiers hold the room air at a dry level. Compared with carpet or drywall it is slower, commonly a week or more. Hold off on the sander until every board is fully dry. If cupped boards are sanded while still wet, crowning shows up down the road.
It depends on the material, how long it stayed wet and how clean the water was. We test before we decide, and we tell you why.
Call (669) 316-8404| Material | Can usually be saved when | Has to be replaced when |
|---|---|---|
| Baseboards and shoe molding | Wood baseboard removed for drying and put back undamaged | Swollen or crumbling shoe molding and MDF base |
| Plywood subfloor | Flat, solid panels that dry back to normal readings | Delaminated plies, spongy areas or mold you can see |
| Paper or felt underlayment | Underlayment beneath boards that are being saved and read dry | Underlayment exposed when boards come up, or with mold on it |
| Floor finish | Light clouding that clears or buffs out once dry | Finish that peels or is stained, requiring sanding and new coats |
| Engineered hardwood | Planks wet only briefly on the surface, edges still tight | Any plank peeling into layers, puffed at edges or damp beneath |
Moisture beneath flooring does not stay put. Cabinets and wall plates do not stop it, so it may enter adjacent rooms or come out at the ceiling one floor down.
Sanding cupped boards flat while they are still wet removes the raised edges. When the wood finishes drying, the centers end up high and the floor is crowned.
Staples and flooring nails corrode when moisture lingers, and their grip weakens. Dark marks from that rust soak into the boards and can be too deep to sand out.
The subfloor can hold moisture long after the boards feel dry. Unless that layer is dried as well, expect renewed cupping or mold on the underside.
We take readings on the boards, the subfloor and unaffected flooring nearby for comparison. From those numbers we learn the depth of the water and if the floor can realistically be saved.
Rugs and furnishings come off the affected boards while pooled water is vacuumed up at once. Boards swell less when the seams stop taking in water sooner.
A vacuum system hooked to mats sealed on the surface lifts moisture out of the boards from above. The room is managed with dehumidifiers so drying stays even and the boards do not crack.
We track readings every day or two until boards and subfloor match dry reference areas. Our final advice is one of three outcomes, no further work, swapping a few boards, or refinishing the floor.
Most of the water ends up beneath the boards, having run down through the joints. Underneath, the wood remains wet even after the face has been dried.
Swelling sets in and board edges lift. Finish may turn cloudy. The bare underside of the boards and the subfloor are where mold can start.
Swelling builds pressure across the floor. With fasteners losing their hold and boards compressing at the edges, some areas can lift away from the subfloor.
Expect a good chance of mold below, dark staining and boards that have buckled. At this stage most of the wet area needs to be replaced rather than dried.
Not seeing your question? Call and ask. It costs nothing to talk it through.
Call (669) 316-8404Take action now and prevent costly damage. Silver Spring Restoration is ready to help.
Call (669) 316-8404 Now